ZyXEL Confidential
Problem Condition: PC1--CPE---DSLAM--PC2，1. Default romfile. 2. Configure the CPE into bridge
mode from Web GUI,Bridge/RFC1483/ DHCP None/NAT disable. VPI/VCI:0/33 LAN:172.25.27.111，3.
PC1 can surf on the Internet. PC1,PC2,CPE are in the same network. 4.”sys quickbrg arp on” in console.
5.The PC2 can not ping the CPE. There is a same issue in P-660HW-D1.
19. [FEATURE CHANGE]
Change modem code to 07.00.04.00
20.[ENHANCEMENT]
Add DRAM random value read and write test in HTP.
21.[Feature update]
Synchronize the reset button behavior ,10 sec: reset to factory default
22.[ENHANCEMENT]
Update copyrighg information to :
Copyright (c) 1994 - 2009 ZyXEL Communications Corp.
23.[ENHNACEMENT]
1. add CI command to disable/enable dying gasp
2. restore ADSL enviroment variable/phy and feature config after reseting ADSL
24.[BUG FIX] [MUST]
Symptom: When we enter command “wan adsl line far” to show US tones, tone 96-127 may show
incorrect number in bit table.
Condition: Input CI command “wan adsl line far” through console or telnet connection. Tone 96-127 will
show number in bit table. The correct display of US should be only one tone xx- xx and the tones 96-127
all should show “0”.
25.[BUG FIX][MUST]
Symptom: User can get rom-0 via http://<IP Address>/rom-0 without authentication. Condition: N/A
26.[BUG FIX][MUST]
Symptom : When use multiboot or Expressboot tool to upgrade the firmware,sometimes will fail.
Condition : Step 1: Connect a PC to Ethernet switch and configure static IP setting for the PC
Step 2: Doubly click the specific ExpressBoot tool or Multiboot tool, then click "Start" button to send the
packets containing the content of firmware. Step 3: Connect the device to switch, then power on the device
and the firmware upgrade will be accomplished automatically Step 4: Sometimes the devices' power light
will become dark to imply that upgrading is fail.
27.[ENHANCEMENT] SPRID : 090220614 , 090330624
Add adjustable MTU solution.
28.[Bug Fix] SPRID: 090421269
Symptom: The web page error in firewall rule edit.
Condition: When entering a range or two subnets as a source or destination for firewall rule, you get the
error message shown in the attached file.
29.[BUG FIX] SPRID: 090421270
Symptom: Pppoa idle issue: while using telnet/WEB GUI from wan to set remote node
Condition: N/A
Note: Not verify
30.[BUG FIX] SPRID: 090421274
Symptom: Pc can't get correct netmask from device.
Condition: if you assign a LAN IP on the 10.x.x.x range, the subnet keeps defaulting to 255.0.0.0 even
though we change it to 255.255.255.0 which is what is required for this particular network
31.[BUG FIX] SPRID: 090421272
Symptom: device will crash will pppoa and syslogs active
Condition: 1.encap pppoa 2.In GUI, Maintenance > Logs > Log Settings, active syslog Logging and enter a
Syslog Server IP Address.
3.In GUI, Maintenance > Logs > Log Settings, acitve Log "System Maintenance".
4.when DSL up, the device will crash.
32.[ENHANCEMENT]
Add Express boot feature.
33.[ENHANCEMENT] Enable/Disable TI CLI log capture by one CI command "wan adsl driver
enableCLI on/off".
Page 7 of 12
(21 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji